Yamaha HTR-6063 Schnellstart Anleitung Seite 3

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 8
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 2
T
I
C
H
I
N
P
U
T
HDMI 2 HDMI 3
HDMI 4 HDMI 5
CENTER
SURROUND SURROUND
BACK/BI-AMP
SINGLE
FRONT
SUBWOOFER
SUR.BACK
N
D
G
ER OUT
+12V
0.1A MAX.
CENTER
M
OTE
AUDIO
OUT
ZONE2
OUT
SURROUND
SUR.BACK
PRE OUT
SUBWOOFER
1
2
FRONT
CENTERSINGLE
SPEAKERS
T
I
C
H
I
N
U
T
H
D
M
I
2
H
D
M
I
3
H
D
M
I
4
H
D
M
I
5
S
U
B
W
O
O
F
E
R
S
U
R
.
B
A
C
K
N
D
G
E
R
O
U
T
+
1
2
V
0
.
1
A
M
A
X
.
C
E
N
T
E
R
M
O
T
E
A
U
D
I
O
O
U
T
Z
O
N
E
2
O
U
T
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
P
R
E
O
U
T
O
O
F
E
R
2
F
R
O
N
T
C
E
N
T
E
R
S
I
N
G
L
E
S
P
E
A
K
E
R
S
6.1
7.1 7.1
- 3 -
1
1
Connect the speakers
Front speaker
R L
Surround back
speaker
R L
Surround
speaker
R L
SubwooferCenter speaker
Connecting the subwoofer
1
C
onnect the subwoofer input jack to the
SUBWOOFER 1 or 2 jack on this unit with an
audio pin cable.
When connecting the presence speakers, refer to “Presence speaker
connection” in the Owner’s Manual.
This unit can connect speakers that support Bi-amp connection for front
speakers. Refer to “Bi-amp connection in the Owner’s Manual for the
details.
7.1
Connect when using with 7.1-channel speaker layout.
6.1
Connect when using with 6.1-channel speaker layout.
Connecting speakers
F
R
O
NT
2
2
3
1
4
4
1
Remove approximately 10 mm of insulation from
the ends of the speaker cables, and twist the bare
wires of the cables together  rmly so that they will
not cause short circuits.
2
Loosen the speaker terminals.
3
Insert the bare wire of the speaker cable into the
gap on the side of the terminal.
4
Tighten the terminal.
2
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than half).
Crossover frequency (if available): Set to maximum.
Subwoofer examples
VOL UME
MIN MAX
CROSSOVER/
HIGH CUT
MIN MAX
Caution:
Remove the AC power cable of this unit from the power outlet
before connecting the speakers.
Generally speaker cables consist of two parallel insulated
cables. One of these cables is a different color, or has a line
running along it, to indicate different polarity. Insert the different
colored (or lined) cable into the “+” (positive, red) terminal
on this unit and the speakers, and the other cable into the “-”
(minus, black) terminal.
Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this unit.
This may damage this unit or the speakers. If the speaker cables
short circuit, “CHECK SP WIRES!” will appear on the front panel
display when this unit is switched on.
This unit is con gured for 8Ω speakers at the factory setting.
When connecting 6Ω speakers, con gure the speaker impedance
setting of this unit to 6Ω. When this unit is con gured for 6Ω
speakers, 4Ω speakers can also be used as the front speakers.
For more information on setting the speaker impedance, refer to
“Changing speaker impedance” in the Owners Manual.
Seitenansicht 2
1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare