1IntroductionFeatures of the CRW2100E DriveHigh speedThe CRW2100E drive supports up to 16X speed writing of a CD-R disc, and up to10X speed writing of
Introduction2*1 Pure-Phase Laser System (patent applied for)Technology that reduces phase interference of the laser beam, so that it shines accurately
3Before UseSystem RequirementsIn order to use the CRW2100E drive, your computer system will need to meet thefollowing set of requirements.n The CRW210
Before Use4Supported DiscsThe CRW2100E drive can write to discs that carry the following logos.
Before Use5About CD-ROMA CD-ROM disc is a compact disc containing high-density read-only data. Ithas many applications, including the playback of mus
6Front and Rear of UnitFront PanelThe CRW2100E drive’s front panel features the following:Eject buttonPress this button when you need to open or close
Front and Rear of Unit7Rear PanelThe CRW2100E drive’s rear panel features the following:AUDIO OUTDIGITAL ANALOGDGCSELSLAVEMASTERRGL+5VDC INPUTG+12V
8Setup FlowchartThis flowchart shows the procedure for setting up the CRW2100E drive. Foreasy cross-referencing, the relevant pages in this manual ar
9Setup Procedures
Setup Procedures10Connecting the CRW2100E DriveOpening the Computer1 Power down your computer and unplug it from the AC outlet.If you proceed without
COMPLIANCE INFORMATION STATEMENT(DECLARATION OF CONFORMITY PROCEDURE)Responsible Party: Yamaha Corporation of AmericaAddress: 6600 Orangethorpe Ave.Bu
Setup Procedures11● As an additional drive (set as secondary slave)If the casing of your computer has a spare 5.25-inch drivebay available, such as wi
Setup Procedures Additional DriveReplacing Drive125 Remove the front cover of a vacant 5.25-inch drive bay slotin the computer.n When you finish this
Setup Procedures Additional DriveReplacing Drive136 Disconnect all the cables connected to the rear of theexisting CD-ROM drive, and also disconnect t
Setup Procedures Additional DriveReplacing Drive147Remove the four screws holding the CD-ROM drive in place, thenslide the drive forward and out of th
Setup Procedures15Setting the Jumper Switches8 Set the CRW2100E drive as master or slave to meet yourcomputer environment by plugging the included pla
Setup Procedures Additional DriveReplacing Drive16Installing the CRW2100E Drive9 Slide the drive backwards into the slot.n Do not apply excessive forc
Setup Procedures Additional DriveReplacing Drive17) Leave enough room behind the drive to connect the power,IDE and audio cables. Then tighten the fo
Setup Procedures18! Connect the IDE cable.Connect the 40-pin IDE cable to the secondary IDE connector onthe motherboard and to the IDE interface conne
Setup Procedures19@ Connect the audio cable between the CRW2100E drive and thecomputer’s sound card, or the motherboard’s audio connector if it hasbui
Setup Procedures20# Connect a 4-pin power cable to the power supply connector of theCRW2100E drive marked “DC INPUT.”CSELSLAVEMASTERIDEINTERFACECONNEC
Setup Procedures Additional DriveReplacing Drive21$ Tighten the four fastening screws on the side of theunit securely using a screwdriver.
Setup Procedures Additional DriveReplacing Drive22% Attach the outer casing of the computer and any screwsthat were removed.
Setup Procedures Additional DriveReplacing Drive23^ Reconnect the computer to the AC outlet and power it up.
Setup Procedures24Configuring in the Operating System& When using Windows 95/98/98 Second Edition, after thecomputer’s operating system has loaded
Setup Procedures25* When using Windows 95/98/98 Second Edition, follow Step & to openthe “Device Manager” window, then double-click the “YAMAHACRW
26OperationThis section explains how to operate the CRW2100E drive after you haveinstalled it. You can load and eject a disc (as described below) only
Operation27n The disc tray will not open if the computer is not switched on. With the CRW2100Edrive powered on, pressing the Eject button will not ope
28TroubleshootingPlease also refer to the YAMAHA CD-R/RW Drives web site for more information.YAMAHA CD-R/RW Drives web site URL:http://www.yamaha.co.
Troubleshooting29The disc keeps being ejected.● Has the disc been placed on the disc tray correctly?The drive does not operate correctly.● Is the disc
Troubleshooting30The “Buffer Underrun” error message is displayed.● Try the following:• Lower the writing speed setting.• Create an image file of the
31AppendixWriting ModesDisc-at-Once (DAO)This mode is used when writing a complete disc in a single pass without pausing.Data cannot be added later, e
Appendix32Session-at-Once (SAO)As a writing method that combines the advantages of the above-mentioned “Disc-at-Once” and “Track-at-Once,” you can com
Appendix33About the firmwareFirmware is a small piece of software built into the CRW2100E drive, and is used tooperate the drive. Since it resides in
Appendix34LED Indicator MessagesThe CRW2100E drive properly installed inside the computer will indicate thefollowing LED messages while the drive (and
Appendix35Writing Methods Disc-at-Once (DAO)Session-at-Once (SAO)Track-at-Once (TAO)Packet WritingWriting/Reading Speed Writing CD-R 1X, 2X, 4X, 8X, 1
Appendix36Audio Out Analog audio output Frequency range: 20 – 20,000 Hz Output level: 700mVrmsDigital audio outputPower Consumption 11W (when
Appendix37IndexSymbols4-pin power cable ...204-pin power connector ...13Aadditional drive...
EUROPE, EASTERN EUROPE andRUSSIAYamaha EUROPA GmbHYamaha Systems Technology EUROPESiemensstrasse 22-34,D-25462 Rellingen, GERMANYURL: http://www.yamah
iEnglishOWNER’S MANUAL
iiSAFETY PRECAUTIONSPLEASE READ CAREFULLY BEFORE PROCEEDINGThese precautions explain how to use the device correctly and safely, thereby preventing in
iii CAUTIONAlways follow the basic precautions listed below to avoid the possibility of physical injury toyourself or others, or damage to the instrum
iv About CD-R/RW discsPlease read the following regarding the handling of CD-R/RW discs.1. Do not expose discs to excessive heat such as in direct su
vTable of Contents©2000 Yamaha Corporation. All Rights Reserved.This document may not, in whole or in part, be copied, photocopied,reproduced, transla
Kommentare zu diesen Handbüchern