Yamaha RX-V365 Bedienungshandbuch PDF herunterladen (Seite 21)

17 En

Optimizing the speaker setting for your listening room (YPAO)

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Notes

• During the automatic setup procedure, do not perform any

operation on this unit.

• We recommend that you get out of the room while this unit is in the

auto setup procedure. It takes approximately 3 minutes for this unit

to complete the auto setup procedure.

6 When all measurements are completed

successfully, “FINISH” appears on the front

panel display.

The result of the automatic setup for each speaker

appears in order on the front panel display.

• To display the result of the automatic setup again, press lk / n

repeatedly.

Notes

• If you select “RELOAD” in step 4, no test tones are output.

• If an error occurs during the “AUTO:CHECK” procedure, the

setup procedure is canceled and an error screen appears. For

details, see “If an error screen appears” on page 17.

• When this unit detects potential problems during the “AUTO

SETUP” procedure, “WARNING” and the warning messages

appear after this unit displays the result of the automatic setup. For

details, refer to the “AUTO SETUP” section in “Troubleshooting”

on page 41.

• The distance measurement result may be longer than the actual

distance depending on the characteristics of your subwoofer.

7 Press ol / h to select “SET” or “CANCEL.”

8 Press oENTER to confirm your selection.

“AUTO SETUP” appears on the front panel display.

9 Press kMENU to exit from “SET MENU.”

10 Disconnect the optimizer microphone from

this unit.

The optimizer microphone is sensitive to heat. Keep it

away from direct sunlight and do not place it on top

of this unit.

• If you change speakers, speaker positions, or the layout of your

listening environment, run “AUTO SETUP” again to recalibrate

your system.

• When you want to check the result of the automatic setup in detail

or manually adjust the parameters, use “MANUAL SETUP” (see

page 32).

■ If an error screen appears

If this unit detects the potential problems, an error

message appears on the front panel display during the

automatic setup.

For details about each error message, see the “AUTO

SETUP” section in “Troubleshooting” on page 41.

After a few seconds later, the following choices appear.

Press ol / h to select “RETRY” or “EXIT” and then

press oENTER.

■ If “WARNING” appears

When this unit detects potential problems during the

automatic setup procedure, “WARNING” appears on the

front panel display after result of each speaker. Check the

warning messages to correct your speaker settings.

Note

• Warnings differ from errors in that warnings do not cancel the automatic

setup procedure.

Press on to display the detailed information

about the warning.

The detailed information about the warning is displayed

and the indicators of inapplicable speakers blink on the

front panel display.

• For details about each warning message, see the “AUTO SETUP” section

in “Troubleshooting” on page 41.

Choice Function

SET* Confirms the “AUTO SETUP” results.

CANCEL Cancels the “AUTO SETUP” results.

FL: 3.3m +2

The distance between the speaker

and the listening position

The result of the

adjustment of the

volume level

Speaker

FL/FR: Front left/right

C: Center

SL/SR: Surround left/right

SW: Subwoofer

Choice Function

RETRY* Starts the “AUTO SETUP” again.

EXIT Exits from the “AUTO SETUP” procedure.

PHASE REVERSED

LFE

LCR

SL SR

Flashes

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 195 196

Kommentare zu diesen Handbüchern

Keine Kommentare

Yamaha RX-V365 Bedienungshandbuch Seite 21

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für AV-Receiver Yamaha RX-V365