Yamaha MG82CX Bedienungshandbuch PDF herunterladen (Seite 12)

MG82CX/MG102C Owner’s Manual

Front & Rear Panels

Reference

3 RETURN L (MONO), R Jacks

These are unbalanced phone-jack type line inputs. The signal

received by these jacks is sent to the STEREO L/R buses.

These jacks are typically used to receive the signal returned

from an external effect device (reverb, delay, etc.).

These jacks can also be used as an auxiliary stereo

input. If you connect to the L (MONO) jack only, the

mixer will recognize the signal as monaural and will

send the identical signal to both the L and R jacks.

4 SEND EFFECT (AUX) Jack

This is an impedance balanced* phone-jack type output that

outputs the signal from the EFFECT (AUX) bus. You can use

this jack, for example, to connect to an external effect unit.

5 STEREO OUT (L, R) Jacks

These are impedance balanced* phone-jack type outputs that

output the signals adjusted by the STEREO Master control.

You can use these jacks, for example, to connect to the power

ampliﬁer driving your main speakers.

6 MONITOR (L, R) Jacks

These are impedance balanced* phone-jack type outputs that

output the signals adjusted by the MONITOR/PHONES con-

trol. Connect these jacks to your monitor system.

7 PHONES Jack

Connect a pair of headphones to this stereo phone jack. The

PHONES jack outputs the same signal as the MONITOR

OUT jacks.

8 PHANTOM +48 V Switch

This switch toggles phantom power on and off. When the

switch is on the mixer supplies +48V phantom power to all

channels that have XLR mic input jacks (CHs 1–5/6).

Turn this switch on when using one or more phantom-pow-

ered condenser microphones.

When this switch is on the mixer supplies DC +48 V

power to pins 2 and 3 of all XLR-type MIC INPUT

jacks.

9 RETURN Control

Adjusts the level at which the signal received at the

RETURN jacks (L (MONO) and R) is sent to the STEREO

L/R bus.

If you supply a signal to the RETURN L (MONO)

jack only, the mixer sends the same signal to both the

L and R Stereo buses.

0 POWER Indicator

This indicator lights when the mixer’s power is ON.

A Level Meter

This LED meter displays the level of the signal sent to the

MONITOR jacks and the PHONES jack. The “0” segment

corresponds to the nominal output level. The PEAK segment

lights red when the output reaches the clipping level.

B 2TR IN

• 2TR IN Switch

If it is set to TO STEREO ( ), the signals are sent to the

STEREO L/R buses. If this switch is set to TO MONITOR

( ), the signals input via the 2TR IN jacks are sent to the

MONITOR OUT jacks, the PHONES jack, and the level

meter. The MONITOR MIX feature becomes available when

it is set to TO MONITOR ( ).

* : When overdubbing, you can adjust the levels

of the monitor playback signal and the signal

being recorded separately.

MONITOR MIX Signal Flow

• 2TR IN control

Adjusts the level of the signal sent from the 2TR IN jacks to

the STEREO L/R buses.

C MONITOR/PHONES Control

Controls the level of the signal output to the PHONES jack

and the MONITOR jacks.

D STEREO Master Control

Adjusts the signal level sent to the STEREO OUT jacks.

* Impedance Balanced

Since the hot and cold terminals of impedance balanced output

jacks have the same impedance, these outputs are less affected by

induced noise.

•

Be sure to leave this switch off ( ) if you do

not need phantom power.

•

When tuning the switch on ( ), be sure that

only condenser mics are connected to the XLR

input jacks (CHs: 1 to 5/6). Devices other than

condenser mics may be damaged if connected

to the phantom power supply. Note, however,

that the switch may be left on when connecting

to balanced dynamic microphones.

•

To avoid damage to speakers, be sure to turn off

ampliﬁers (or powered speakers) before turning

this switch on or off. We also recommend that

you turn all output controls (STEREO Master

control, etc.) to their minimum settings before

operating the switch to avoid the risk of loud

noises that could cause hearing loss or device

damage.

NOTE

CAUTION

NOTE

Playback

signal

Recording

signal

2TR IN

2TR IN Control

STEREO Master Control

MONITOR/PHONES Controls

STEREO

buses

REC OUT

MONITOR/

PHONES

jacks

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 20 21

Kommentare zu diesen Handbüchern

Keine Kommentare

Yamaha MG82CX Bedienungshandbuch Seite 12

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audiomischer Yamaha MG82CX