Yamaha MG82CX Bedienungshandbuch PDF herunterladen (Seite 15)

MG82CX/MG102C Owner’s Manual

Reference

Troubleshooting

* The MG82CX feature is described ﬁrst, followed by the MG102C feature in brackets: MG82CX (MG102C).

■ Power doesn’t come on. ❑ Is the supplied power adaptor properly plugged into an appropriate AC wall outlet?

❑ Is the supplied power adaptor properly plugged into the mixer?

■ No sound. ❑ Are microphones, external devices, and speakers connected correctly?

❑ Are the channel GAIN controls, LEVEL controls, STEREO Master control set to

appropriate levels?

❑ Is the MONITOR switch set properly?

❑ Are your speaker cables connected properly, or are they shorted?

❑ If the above checks do not identify the problem, call Yamaha for service. (Refer to

the page 59 for a list of service centers.)

■ Sound is faint,

distorted, or noisy.

❑ Are the channel GAIN controls, LEVEL controls, STEREO Master control set to

appropriate levels?

❑ Are two different instruments connected to the XLR-type and phone jacks, or to the

phone and RCA pin jacks on one channel? Please connect to only one of these

jacks on each channel.

❑ Is the input signal from the connected device set to an appropriate level?

❑ Are you applying the effects at an appropriate level?

❑ Are microphones connected to the MIC input jacks on channels 1 to 5/6?

❑

If you are using condenser microphones, is the PHANTOM +48 V switch turned ON?

■ No effect is applied.

(If you are using

MG82CX)

❑ Check that the EFFECT control on each channel is correctly adjusted.

❑ Be sure that the internal effect unit’s ON switch is turned ON.

❑ Be sure that the EFFECT PARAMETER control and EFFECT RTN control are cor-

rectly adjusted.

■ I want spoken words to

be heard more clearly.

❑ Be sure that the switches are ON.

❑ Adjust the equalizers (HIGH, MID and LOW) on each channel.

■

I want to output a monitor

signal through speakers.

❑ Connect a powered speaker to the EFFECT (AUX) jack*. Then adjust the output

signal by using the EFFECT (AUX) controls* on each channel.

Mounting to a Microphone Stand

Turn the mixer upside-down, and hold the

microphone-stand adaptor (BMS-10A; sold

separately) against the bottom of the mixer

so that the screw holes are aligned (

1).

Screw the adaptor ﬁrmly into place with the

two screws (

2).

Turn the mixer right-side up, and mount it

onto your microphone stand.

Loosen the angle adjustment wingnut (1),

adjust the mixer’s angle as desired (

2), and

then tighten the wingnut securely (

3).

For more information, refer to the BMS-10A Owner’s

Manual.

•

When using the mixer on a microphone stand, be

sure to set the stand on a level and stable sur-

face. Do not set up the stand in locations subject

to vibrations or wind.

•

Note that mixer may be damaged if the stand

should fall over. Attach the connection cables care-

fully so that the cables will not catch on the equip-

ment and cause it to fall. For example: arrange the

cables so that they run parallel with the micro-

phone pole down to the base of the stand.

•

Leave ample free space around the stand.

CAUTION

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 21

Kommentare zu diesen Handbüchern

Keine Kommentare

Yamaha MG82CX Bedienungshandbuch Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audiomischer Yamaha MG82CX