Yamaha CBX-D3 Installationshandbuch

Chapter 8Audio Driver8.1Why Audio Drivers?Logic automatically recognizes what audio hardware is avail-able on your computer, and configures itself acc

Chapter 8Audio DriverYou can also check whether there are any communicationproblems with your hardware-for example if your hardwareis not being recogn

DAEcan select either 44.1 or 48 kHz This parameter corresponds tothe setting in the Audio menu.Sync ModeThis is where you select the source for the sy

Chapter 8Audio DriverIf you are using an audio interface with more than one pair ofdigital inputs (e.g. an 888 I/O), you will also be able to selectan

DAE Session 8 / ProTools ProjectThe first time you start the program with Session 8 or ProToolsProject hardware, and DAE Version 2.95 or later, Logic

Chapter 8Audio DriverYou use this window to set the various Session 8 routingoptions. For more on these options, please refer to the Session8 manual.A

CBXGold version without any disadvantages. Platinum supports TDMsystem instead.OverviewsSession 8 hardware cannot calculate, or display any overviews(

Chapter 8Audio Driverhappens after booting up LOGIC Audio), the message "Initial-izing CBX" will appear on the screen.The CBX-D3's samp

DR 8116I11, or complete the calculation more quickly by bringing it intothe foreground (Finish). If you select this option, you will notbe able to per

Chapter 8Audio DriverThis may cause SCSI noise. You can switch off this functionunder Audio > Audio Hardware & Drivers > Request Level-meter

DR 8/16Audio window:All DR files used in the Arrange are automatically added anddisplayed in the Audio window as usual.The Audio window allows all DR

Chapter 8Audio DriverAvailable Drivers~ Any Audio hardware requires an appropriate driver as a commu-nication link to the Logic software. Some of the

Chapter 8Audio Driver8.6 1212 I/OSystem RequirementsYou need a PowerMac, or MacOS compatible computer withPCI expansion slots to run a Korg 1212 I/O.

1212 I/ODriversDe/ReactivatingIf you wish to run Logic without the 1212 Extension, or anyother audio drivers-in other words, simply as a MIDIprogram-d

Chapter 8Audio DriverOutput RoutingIn every Track Object, you can choose the output pair, by usingthe lower button in the I/O section. Select either t

TDM HardwareHowever, you should always use a drive from the approved listprovided by Digidesign.System RequirementsTo operate with TDM support, you wi

Chapter 8Audio DriverClick on the check box by the word "TDM" (see above).The "x" will disappear, and you can now use your ProTool

TDM HardwareObject Parameters of TDM Audio ObjectsFor general information on the audio object parameters, see thesection The Object Parameter Box on p

Chapter 8Audio DriverYou can also use the Aux Object with a bus input as Aux MasterSend for an external effects device. Select an output of theaudio i

TDM HardwareIn the header line of the Plug-in window, you can open theSetups pull-down menu by clicking on the arrow button:Copy SetupPaste Setup Save

Chapter 8Audio DriverDisabled Plug-insIf you haven’t done so, create a folder with the name “Plug-ins(unused)” in your DAE folder (or in any other loc

TDM Hardwareone plug-in, in the first position (first slot), you can automate 64parameters in this location: 64-127.If you insert an additional plug-i

Why Audio Drivers?Lo@“Direct I/O”. If you use an older PCI card, such as an Audiome-dia III or a ProTools System, please be aware that you maycontrol

Chapter 8Audio Driverdraw function (which also is available as a key command), Hyper-draw will set itself automatically for the first used controller.

TDM Hardware Special Features of ProTools III with 32 or 48 TracksLogic Audio supports 32 or 48 track ProTools III systems, withmore than one Disk I/O

Chapter 8Audio DriverIf you operate more than one audio interface (through addi-tional Bridge I/O cards), the additional interfaces are called "b

TDM HardwareThe 24-bit mixer requires more DSP capacity than the 16-bitmixer. Therefore, you may get a DAE error message ("DSPsmaxed out”), when

Chapter 8Audio DriverAfter confirming the dialog, the audio files will be copied-thecopied files will have the selected word length. Logic now will as

TDM HardwareCorresponding Audio ObjectsBased on the connected hardware, and the installed extensions,this song will include audio objects that corres

Chapter 8Audio DriverTotal Number of Audio TracksWhen operating different audio hardware simultaneously, thenumber of possible tracks cannot be determ

TDM HardwareHardware Setup- InterfaceOptions:Interface Port:Each of the two groups of up to eight channels can be individ-ually connected to a Disk I/

Chapter 8Audio DriverPlayback Engine Setup7Playback Engine: -r Interface Options:@ d24Card:Interface Port:mInterface:flOFlT Bridge B cl-81 I-,Sync Mod

Direct I/Oavailable. Furthermore, you should only play back audio filesfrom the hard drive attached to SCSI bus of your Power Macin-tosh, and NOT from

Chapter 8Audio DriverDirect I/OThis is the driver for newer Digidesign products like Project II,that can’t be controlled by DAE. Direct I/O may also b

Chapter 8Audio Driver8.9 Sonorus StudI/OIn comparison with the ASIO driver, this direct support of theStudI/O offers the following advantages: Better

ASIO(in this case Logic Audio Platinum) to work together. An ASIOdriver translates the input data of the hardware into a specificformat, and transfers

Chapter 8Audio Driverpanel exists depends on the manufacturer of the hardwarebeing supported.Clock SourceThis setting allows you to use a digital cloc

8.11 Yamaha DSP FactoryThe currently supported components of the Yamaha DSPFactory System include one DS2416 card and, optionally, up totwo AX44 exten

Chapter 8Audio DriverMixerThe mixer directly reflects the available DSP and routing of theDSP Factory, as long as you use the ASIO Driver DS 2416 asth

Yamaha DSP Factoryother hand, it might be useful to directly record EQs anddynamics.On the effect return channel, the internal multi-effects devicesal

Chapter 8Audio Driver DS2416 + AX16: 8 Inputs and 6 Outputs (2 more Outputs canbe used in parallel with the internal effect busses; Recordingbusses ar

Yamaha DSP FactoryLogicDS2416 RoutingYou can open this window with akey command or from the audiowindow Options > DS2416 Rout-ing.The left half is

Chapter 8Audio Driverthis message with USE, the internal sample rate will be set tothe detected rate.8-48

Audio Engine8.2 Audio EngineThe features available vary somewhat from driver to driver.The Audio Engine used for Audiowerk, Mac AV, Korg 1212,Direct I

Chapter 8Audio DriverCommon ParametersThe drivers mentioned above not only have the audio engine,but therefore also the following parameters in common

Audio Enginerates, not only that twice the space on the hard disk will beneeded, but also that the Audio Engine will be required to per-form twice as

Chapter 8Audio Driver When in doubt - e.g. if you own an older Power Macintosh model but are using aG3 card - experiment. Experiment to find the setti

DAEAfter changing the Universal Track Mode setting, you have to reboot Logic beforethe change will take effect.8.3 DAEWith Logic Audio, the Digidesign