Yamaha CL5 Handbuch Seite 178
- Seite / 302
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Recorder
Reference Manual
178
4 Sub-directory
Indicates each song's track number, the name of upper level directory, and whether a
sub-directory exists (in the case that the directory has been selected).
• Upper level............Press this to move up to the directory that is one level higher than
the current one.
• Sub-directory................Press this to move to that sub-directory.
NOTE
• If you switch folders, that folder will be selected as the recording destination.
• The folders that can be selected are restricted to the SONGS folder inside the YPE folder, and
folders located below the SONGS folder.
5 PLAY check symbol
Enables you to select multiple files that will be played back consecutively.
6 SELECT knob
Use the multifunction knob to select a song.
7 NOW PLAYING button
Press this button to always select the currently-playing song on the list.
8 MOVE UP/MOVE DOWN buttons
Change the order of the selected song in the list.
9 Display switch buttons
Switch the list between the SONG TITLE display and the FILE NAME display.
0 SAVE LIST button
Saves the order of the current title list and PLAY check symbol settings as a playlist.
A RELOAD button
Loads the playlist that was saved most recently. Use this button to revert the current
playlist you are editing back to the previous state.
PLAY MODE field
Sets the playback method of the currently selected song.
B SINGLE button
If this button is on, the recorder will stop after playback of the current song is complete.
If this button is off, the recorder will play the next song on the list after playback of the
current song is complete.
C REPEAT button
If this button is on, after playback of the current song is complete, the recorder will play
the first song on the list that is marked with a PLAY check symbol (unless there are no
subsequent songs that are marked with a PLAY check symbol).
If this button is off, the recorder will stop after playback of the current song is complete
(unless there are no subsequent songs that are marked with a PLAY check symbol). One
of the following playback methods is selected according to the on/off settings of the
SINGLE button and the REPEAT button.
Editing the title list
You can change the order of the audio files shown in the title list, and edit the titles or artist
names.
NOTE
• If the title or artist name contains characters that cannot be displayed, these characters will be
converted into ? for display.
• The title and the artist name can be edited only for MP3 format audio files.
SINGLE
button
REPEAT
button
Mode
On On
The currently-selected song will play repeatedly until you stop
playback.
On Off The currently-selected song will play once and then stop.
Off On
Songs with the PLAY checkmark selected are played in order,
starting with the currently-selected song, and then they are
played again from the first song in the title list. The currently-
selected song will play repeatedly until you stop playback.
Off Off
Songs with the PLAY checkmark selected are played in order,
starting with the currently-selected song. After the final song in
the title list is played, playback stops.
STEP
1. Connect a USB flash drive containing audio files to the USB connector.
2. In the Function Access Area, press the RECORDER button.
3. Press the No. button and the change directory icon in the RECORDER screen to view
a list of the contents of the folder that includes the desired file.
4. If you want to edit a title in the title list, press the SONG TITLE/FILE NAME EDIT
button. If you want to edit the artist name, press the ARTIST EDIT button.
5. Edit the title or artist name, and press the OK button.
6. If necessary, use the SONG TITLE/FILE NAME SORT button, ARTIST SORT button,
and MOVE UP/MOVE DOWN buttons on screen to change the order of the title list.
7. When editing is complete, press the SAVE LIST button to save the changes.
- Reference Manual 1
- Table of contents 2
- Function Tree 4
- SELECTED CHANNEL section 10
- Reference Manual 10
- Centralogic section 12
- OVERVIEW Screen 13
- TO STEREO/MONO field 15
- 1 TO STEREO PAN knob 15
- 2 ST/MONO indicator 15
- DCA group field 15
- Mute group field 15
- Input and output patching 16
- Changing the input patching 17
- Changing the output patching 18
- PATCH/NAME screen 19
- CH SELECT screen 20
- PORT SELECT screen 23
- Input channels 26
- HA (head amp) settings 29
- GAIN/PATCH window (8ch) 30
- GAIN/PATCH window 32
- STEREO/MONO bus 33
- TO STEREO/MONO window (8ch) 34
- TO STEREO/MONO window 35
- MATRIX bus 37
- Using the Centralogic section 38
- MIX SEND/MATRIX SEND window 38
- SENDS ON FADER mode 40
- INPUT DELAY screen (8ch) 41
- 1 DELAY SCALE button 42
- 2 Channel select button 42
- L-MONO 42
- R-MONO 42
- LR-MONO 43
- Setting procedure 43
- 1 LR-MONO SELECT field 43
- 2 LR-MONO SELECT button 43
- Setting Surround mode 44
- SELECTED CHANNEL VIEW screen 44
- OVERVIEW screen 45
- SURROUND PAN 1CH screen 46
- 64/ST IN (CL3), ST IN (CL1)) 46
- TO STEREO/MONO screen 47
- Channel library operations 48
- OUTPUT channels 49
- MONO bus 51
- ST IN (CL1), OUTPUT) 52
- MONO channels to MATRIX buses 53
- MATRIX SEND screen 54
- OUTPUT PORT screen 56
- EQ and Dynamics 58
- HPF/EQ window (8ch) 60
- Using dynamics 61
- DYNAMICS1/2 window (8ch) 63
- EQ library 64
- Dynamics library 64
- Channel Job 65
- Controlling DCA groups 67
- DCA ROLL-OUT operation 68
- Operation Example 1 69
- Operation Example 2 69
- Mute group 70
- Using mute groups 72
- Using the Mute Safe function 72
- RECALL SAFE MODE window 74
- Channel Link function 76
- 1 Input channel display field 77
- 2 Link indicator 77
- 3 LINK PARAMETER field 78
- 4 SEND PARAMETER field 78
- 5 INPUT/OUTPUT button 78
- Channel link operations 78
- CH LINK SET window 80
- CH COPY MODE window 81
- 1 SOURCE CH field 82
- 2 DESTINATION CHs field 82
- 3 COPY button 82
- 4 CLOSE button 82
- CH MOVE MODE window 83
- About Mix Minus 84
- Scene memory 86
- SCENE STORE window 87
- SCENE LIST window 88
- Recalling a scene 89
- Editing scene memories 90
- Scene memory editing 91
- Copying and pasting a scene 91
- Clearing a scene 92
- Cutting a scene 92
- Inserting a scene 92
- GLOBAL PASTE window 93
- FOCUS RECALL window 95
- Using the Fade function 96
- FADE TIME window 97
- 2 CURRENT SETTING field 98
- 1 PLAY button 99
- 2 Song select button 99
- 3 Offset time display 99
- 4 CURRENT SETTING field 99
- Using Preview mode 100
- Functions in Preview mode 101
- Monitor and Cue functions 102
- Using the Monitor function 103
- MONITOR screen 104
- MONITOR window 105
- MONITOR SOURCE SETUP screen 108
- Using the Cue function 109
- Operating the Cue function 110
- CUE window 112
- CUE screen (Surround mode) 113
- Talkback and Oscillator 114
- TALKBACK window 115
- Using the Oscillator function 116
- OSCILLATOR window 117
- 3 ASSIGN section 118
- 4 Meter section 118
- 5 OSCILLATOR OUTPUT button 118
- INPUT/OUTPUT/RTA tab 119
- INPUT METER screen 119
- OUTPUT METER screen 119
- Fader level and meter display 120
- Centralogic fader display 120
- METERING POINT field 120
- PEAK HOLD button 120
- SHOW SEND LEVEL button 121
- RTA METER screen 121
- METER screen (Surround mode) 122
- Function Access Area screen 123
- PREMIUM RACK 124
- Virtual rack operations 125
- 4 INPUT PATCH button 126
- 5 OUTPUT PATCH button 126
- 6 Rack container 127
- Graphic EQ operations 128
- Inserting a GEQ in a channel 129
- GEQ EDIT window 129
- Using the 31BandGEQ 130
- GEQ EDIT window (31BandGEQ) 130
- Using the Flex15GEQ 131
- GEQ EDIT window (Flex 15GEQ) 131
- Parametric EQ operations 132
- PEQ EDIT window 132
- PEQ EDIT window (8PEQ) 133
- About AUTOMIXER 135
- Editing the internal effects 137
- STEREO type effects 138
- MIX type effects 138
- 1 Effect title/type 139
- 2 Input/output meters 139
- EFFECT EDIT window 140
- Using the Tap Tempo function 141
- Using the Premium Rack 144
- Linked in reverse 151
- Premium Rack libraries 153
- Using an I/O device 154
- DANTE INPUT PATCH window 155
- PORT SELECT window 155
- OUTPUT PATCH window 156
- I/O DEVICE screen (I/O page) 156
- I/O DEVICE HA window 158
- Remotely controlling an amp 159
- Using an external head amp 160
- Daisy chain network 161
- Ring connection 162
- EXTERNAL HA window 164
- Basic MIDI settings 165
- 1 TERMINAL field 167
- 2 PORT NO. field 167
- 3 OK button 167
- 1 CH field 167
- 2 OK button 167
- 1 PROGRAM CHANGE field 168
- 2 PROGRAM CHANGE MODE field 168
- MIDI PROGRAM CHANGE window 169
- MIDI CONTROL CHANGE window 172
- Recorder 173
- CH SELECT window 174
- 3 4A0987 5 6 175
- RECORDER screen 177
- Editing the title list 178
- Required devices and software 179
- Word clock settings 180
- Dante Accelerator settings 180
- Audio recording and playback 181
- Setting up Dante Controller 181
- Setting up DAW software 181
- Preparing the project 182
- Recording into a project 182
- NUENDO LIVE SETUP window 183
- Playing a multi-track project 185
- About the SETUP screen 186
- BUS SETUP field 187
- D BUS SETUP button 187
- E SURROUND SETUP button 187
- User settings 188
- CREATE USER KEY window 190
- Logging-in 191
- Changing the password 192
- Changing the user level 193
- USER SETUP window 194
- Preferences 195
- 2 PATCH field 196
- 3 LOCALE SETUP field 196
- 4 ERROR MESSAGE field 196
- 5 PANEL OPERATION field 196
- USER DEFINED keys 197
- USER DEFINED knobs 203
- About TOUCH AND TURN 204
- Function 205
- Assignable encoders 206
- Custom fader bank 208
- Master fader 209
- Custom fader bank functions 210
- Console Lock 210
- Unlocking the console 211
- SAVE/LOAD window 212
- SAVE SELECT screen 213
- LOAD SELECT screen 215
- 1 2 3 4 5 216
- Formatting a USB flash drive 217
- Word clock and slot settings 218
- WORD CLOCK/SLOT SETUP window 219
- Using cascade connections 220
- 2 CASCADE LINK MODE buttons 221
- BUS SETUP window 223
- 1 2 3 4 5 6 7 224
- Setting the network address 225
- Dante audio network settings 226
- Daisy chain connections 230
- Redundant connections 230
- DANTE SETUP window 231
- 1 DEVICE LABEL 233
- 2 INPUT/OUTPUT knobs 233
- 3 Device label entry keyboard 233
- REMOTE HA settings 234
- REMOTE HA SELECT window 234
- Displaying the device status 235
- Messages 235
- Error messages 236
- Warning messages 236
- Using GPI IN 237
- MIDI/GPI screen (GPI page) 238
- Using GPI OUT 239
- Using FADER START 240
- Help function 243
- Other functions 245
- Warning/Error Messages 250
- Data List 254
- EQ Library List 255
- DYNAMICS Library List 256
- Data List 257
- * At fs=44.1 kHz 257
- Dynamics Parameters 258
- COMPRESSOR 259
- EXPANDER 259
- Effect Type List 260
- Effects Parameters 261
- STEREO REVERB 262
- EARLY REF 262
- GATE REVERB, REVERSE GATE 262
- MONO DELAY 262
- STEREO DELAY 262
- MOD. DELAY 263
- DELAY LCR 263
- CHORUS 263
- FLANGE 264
- SYMPHONIC 264
- PHASER 264
- DYNA.FLANGE 264
- DYNA.PHASER 265
- HQ.PITCH 265
- DUAL PITCH 265
- TREMOLO 265
- AUTOPAN 266
- ROTARY 266
- RING MOD 266
- MOD.FILTER 266
- DYNA.FILTER 266
- REV+CHORUS 267
- REVCHORUS 267
- REV+FLANGE 267
- REVFLANGE 267
- REV+SYMPHO 268
- REVSYMPHO 268
- REVPAN 268
- DELAY+ER 268
- DELAYER 269
- DELAY+REV 269
- DELAYREV 269
- DISTDELAY 270
- MULTI FILTER 270
- FREEZE 270
- DISTORTION 270
- AMP SIMULATE 271
- COMP276 271
- COMP276S 271
- COMP260 271
- COMP260S 271
- EQUALIZER601 272
- OPENDECK 272
- M.BAND DYNA 272
- M.BAND COMP 273
- Portico5033 273
- Portico5043 273
- Opt-2A 274
- Dynamic EQ 274
- Buss Comp 369 274
- Automixer Parameters 275
- NRPN Parameter Assignments 279
- Input channels 283
- Parameter Stereo 284
- MIX Channels 285
- MATRIX Channels 286
- STEREO, MONO Channels 287
- Parameters 288
- MIDI Data Format 289
- 2 SYSTEM REALTIME MESSAGE 290
- 3 SYSTEM EXCLUSIVE MESSAGE 290
- 4 PARAMETER CHANGE details 291
- ANALOG INPUT CHARACTERISTICS 296
- ANALOG OUTPUT CHARACTERISTICS 296
- CONTROL I/O CHARACTERISTICS 297
- Electrical Characteristics 298
- Mixer Basic Parameters 299
- MIDI Implementation Chart 301
Verwandte Produkte und Handbücher für Software Yamaha CL5
Software Yamaha MOXF8 Bedienungshandbuch
(57 Seiten)
(57 Seiten)
Software Yamaha Amp Editor Bedienungshandbuch
(211 Seiten)
(211 Seiten)
Software Yamaha CL5/CL3/CL1 V1.5 Bedienungsanleitung
(277 Seiten)
(277 Seiten)
Software Yamaha V4.0 Bedienungshandbuch
(526 Seiten)
(526 Seiten)
Software Yamaha V3 Bedienungshandbuch
(83 Seiten)
(83 Seiten)
Software Yamaha MOX6 Handbuch
(160 Seiten)
(160 Seiten)
Software Yamaha XF6 Handbuch
(255 Seiten)
(255 Seiten)
Software Yamaha MOXF8 Handbuch
(163 Seiten)
(163 Seiten)
Software Yamaha MOX6 Bedienungshandbuch
(57 Seiten)
(57 Seiten)
Software Yamaha PSR-S975 Handbuch
(136 Seiten)
(136 Seiten)
Software Yamaha Tyros3 Handbuch
(130 Seiten)
(130 Seiten)
Software Yamaha FP7210A Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Software Yamaha HS650A Bedienungsanleitung
(2 Seiten)
(2 Seiten)
Software Yamaha HS850 Bedienungsanleitung
(1 Seiten)
(1 Seiten)
Philips 58PFL4609-F7 manuels
Manuels d'utilisation et guides de l'utilisateur pour Vidéo Philips 58PFL4609-F7.
Nous fournissons des manuels en pdf 2 Philips 58PFL4609-F7 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern